12/100VDC-100/800/900/1000/1500VDC

Sello hermético de metal-cerámica Rendimiento a altas temperaturas Baja resistencia de contacto durante toda la vida útil Cumple con la directiva RoHS 2011/65/UE CARACTERÍSTICAS Disposición de los contactos: forma X, SPST NO Tensión máxima de conmutación: 750 VCC Corriente continua (conductor de 60 mm²) 250 A Corriente de sobrecarga 20 segundos 1.000 A 2 minutos…

Sellado hermético con relleno de gas. Contactos auxiliares: para la señal de posición principal. Economizador de bobina integrado para reducir la potencia de mantenimiento de la bobina. Conmutación de potencia bidireccional. Cumple con la normativa RoHS 2011/65/UE. Cumple con la norma IEC 60947-4-1.

Sello hermético de metal-cerámica con relleno de gas. Contactos auxiliares opcionales: para la señal de posición principal. Conmutación de potencia bidireccional. Cumple con la directiva RoHS 2011/65/UE. Cumple con el reglamento REACH.

Sellado hermético con resistencia térmica de hasta 175 °C, lo que reduce el riesgo de incendio o fusión en caso de sobrecorriente. Relleno de gas (principalmente hidrógeno) para inhibir eficazmente la oxidación, lo que da como resultado una resistencia de contacto baja y estable. Capacidad de conducción de corriente continua de 400 A a 85…

Hermetically Sealed – Designed to meet: UL1604 for Class I & II, Div 2 and Class III for use in hazardous locations, IP67 for temporary water immersion for 30 min, SAE J1171 – external ignition protection, and ISO8846 for protection against ignition around flammable gasses. Built-in coil suppression for all DC coils – Saves you…

Hermetically Sealed – Designed to meet: UL1604 for Class I & II, Div 2 and Class III for use in hazardous locations, IP67 for temporary water immersion for 30 min, SAE J1171 – external ignition protection, and ISO8846 for protection against ignition around flammable gasses. High Efficiency Dual DC Coils – Very low 12, 24,…

Hermetically Sealed – Designed to meet: UL1604 for Class I & II, Div 2 and Class III for use in hazardous locations, IP67 for temporary water immersion for 30 min, SAE J1171 – external ignition protection, and ISO8846 for protection against ignition around flammable gasses. Built-in coil suppression for all DC coils – Saves you…

Hermetically Sealed – Designed to meet: UL1604 for Class I & II, Div 2 and Class III for use in hazardous locations, IP67 for temporary water immersion for 30 min, SAE J1171 – external ignition protection, and ISO8846 for protection against ignition around flammable gasses. High Efficiency Dual DC Coils – Very low 12, 24,…

GV250 is a very compact contactor for currents up to 250 A and max 1000 V dc. The GV250 exceeds IP67 and IP69K environmental requirements, as well as salt fog according to MIL-STD-810. The GV250 is light and compact (approximately 76x81mm) and hermetically sealed and gas-filled, which means it can be safely used in almost…

Latching/Bi-stable, contacts held magnetically so no coil holding power required. A latching contactor hermetically sealed and developed according to UL1604 and IP67 as well as RoHS and CE. Flame retardant according to SAE J1171 and ISO8846. Mounting is possible in all directions for easy installation.

SPST Normally Open High Voltage Contactors Ceramic seal PCB Mountable (optional) Bi-directional power switching Meets RoHS 2011/65/EU REACH Compliant

Planned launch Q3 2025 Hermetically sealed and rated to 175°C with reduced risk of fire or meltdown under overcurrent conditions. Refilled with gas (mainly hydrogen) to effectively inhibit oxidation, resulting in low and stable contact resistance. Insulation resistance is 1000MΩ (1000Vdc), while the dielectric strength between the coil and contacts reaches 4.0kV. Continuous current of…